Finishing Type X drywall after installation is a crucial step that not only enhances the aesthetic appeal of your space but also ensures the long - term durability and functionality of the drywall. As a trusted Type X drywall supplier, I've witnessed firsthand the transformation that proper finishing can bring to a project. In this blog, I'll guide you through a step - by - step process on how to finish Type X drywall after installation.
Understanding Type X Drywall
Before delving into the finishing process, it's essential to understand what Type X drywall is. Type X drywall is a fire - resistant variant, commonly used in areas where fire protection is a concern, such as between garages and living spaces, or in multi - family dwelling partitions. It has a thicker core and special additives that give it enhanced fire - resistant properties compared to standard drywall. You can learn more about its features on our page Fully Functional Drywall.
Tools and Materials Required
To finish Type X drywall properly, you'll need the following tools and materials:
- Tools: A drywall knife (in various sizes, typically 4 - inch, 6 - inch, and 10 - inch), a taping bucket, a sanding block, a pole sander, a utility knife, and a drywall saw.
- Materials: Drywall mud (also known as joint compound), drywall tape (paper or fiberglass), sandpaper (in various grits, starting from 120 - grit and moving up to 220 - grit), and primers.
Step 1: Taping
The first step in finishing Type X drywall is taping the joints. This process covers the gaps between the drywall panels and helps create a seamless surface.
- Apply the First Layer of Mud: Use a 6 - inch drywall knife to apply a thin layer of drywall mud over the joints. The layer should be about 1/8 - inch thick and extend about 2 - 3 inches on either side of the joint.
- Embed the Tape: Immediately after applying the mud, place the drywall tape over the joint and press it firmly into the mud. Use the drywall knife to smooth out the tape, removing any air bubbles or wrinkles. Make sure the tape is fully embedded in the mud.
- Feather the Edges: Use the drywall knife to feather the edges of the mud on either side of the tape. This will help blend the joint with the surrounding drywall.
Step 2: First Coat of Mud
After the tape has dried (usually within 24 hours), it's time to apply the first coat of mud over the taped joints.
- Apply the Mud: Use a 10 - inch drywall knife to apply a second layer of mud over the taped joints. This layer should be thicker than the first layer used for taping, but still thin enough to be easily sanded later.
- Smooth the Surface: Use the drywall knife to smooth the surface of the mud, removing any bumps or ridges. Feather the edges of the mud to blend it with the surrounding drywall.
- Let it Dry: Allow the first coat of mud to dry completely. This may take 24 to 48 hours, depending on the humidity and temperature of the environment.
Step 3: Second Coat of Mud
Once the first coat of mud is dry, it's time for the second coat.
- Prepare the Surface: Lightly sand the first coat of mud with a 120 - grit sandpaper to smooth out any rough spots. Wipe away the dust with a damp cloth.
- Apply the Second Coat: Use a 10 - inch or 12 - inch drywall knife to apply the second coat of mud. This coat should cover the first coat completely, and you should aim for a smoother and more even surface.
- Smooth and Feather: As before, use the drywall knife to smooth the surface and feather the edges of the mud.
- Dry Time: Let the second coat dry. Again, this may take 24 to 48 hours, depending on the conditions.
Step 4: Third Coat of Mud
The third coat is the final coat of mud and is used to achieve a perfectly smooth surface.
- Sand the Second Coat: Use a 150 - grit sandpaper to sand the second coat of mud. This will further smooth the surface and prepare it for the final coat.
- Apply the Third Coat: Apply a thin layer of mud using a 12 - inch or 14 - inch drywall knife. This layer should be very smooth and even.
- Final Smoothing: Use a drywall knife to smooth the surface of the third coat one last time. Feather the edges to blend with the surrounding drywall.
- Drying: Allow the third coat to dry completely. This may take another 24 to 48 hours.
Step 5: Sanding
Once the third coat of mud is dry, it's time for the sanding process.
- Start with Coarse Grit: Begin by using a 120 - grit sandpaper on a sanding block or pole sander. Sand the entire surface of the drywall, including the joints and any areas where the mud was applied. This will help remove any high spots and rough areas.
- Move to Finer Grit: After sanding with the 120 - grit sandpaper, switch to a 150 - grit or 220 - grit sandpaper. This will give the surface a smoother finish.
- Dust Removal: As you sand, a lot of dust will be generated. Use a vacuum cleaner or a damp cloth to remove the dust from the surface of the drywall.
Step 6: Priming
After sanding, the next step is to apply a primer to the drywall surface.
- Choose the Right Primer: Select a high - quality drywall primer. A good primer will help the paint adhere better to the drywall surface and also seal the pores in the mud.
- Apply the Primer: Use a paint roller or a paintbrush to apply the primer evenly over the entire surface of the drywall. Make sure to cover all areas, including the joints and corners.
- Let it Dry: Allow the primer to dry completely according to the manufacturer's instructions. This may take a few hours to a day.
Step 7: Painting
Once the primer is dry, you can proceed with painting the drywall.
- Choose the Paint: Select a paint that is suitable for the type of room and your aesthetic preferences. For example, in high - traffic areas, you may want to choose a durable, washable paint.
- Apply the Paint: Use a paint roller or a paintbrush to apply the paint evenly over the primed drywall surface. You may need to apply two or more coats of paint for a smooth and even finish.
- Let it Cure: Allow the paint to cure completely. This may take a few days, depending on the type of paint used.
Conclusion
Finishing Type X drywall after installation is a multi - step process that requires patience and attention to detail. By following these steps, you can achieve a professional - looking finish that not only enhances the appearance of your space but also maintains the fire - resistant properties of Type X drywall.
If you're in the process of a project that requires Type X drywall or have any questions about the finishing process, I'd love to assist you. Reach out to us for more information on our products and to start a procurement discussion. We're here to help you make your project a success.

References
- "Drywall Installation and Finishing Guide", National Gypsum Company
- "Fire - Resistant Building Materials Handbook", Building Science Press
